If you have pets, write about them. Geniet mee van onze rustgevende hobby, toer mee zonder haast, zonder stress Je kan hier moppen,Gedichtjes of kleine probleempjes zeggen die je met andere mensen wilt delen. The law requires Maini inzestrate online dating services meeting specific criteria—including having as their primary business to connect U. Kimbo Kamma Kearns. As a 20 year old, you're obviously dsting adult and capable of making your own decisions.
|Published (Last):||5 September 2014|
|PDF File Size:||5.94 Mb|
|ePub File Size:||4.19 Mb|
|Price:||Free* [*Free Regsitration Required]|
Recommend Documents. Kubernetes Up and Running Preview kube up. Advance Steel advance steel book. Advance Steel Brochure. Graitec Advance Steel. Advance Steel xx. Maini Mecanice scoala. Running Another Program With Delphi. You will create a structural model from scratch and then insert automated connection between structural sections.
Visit the Authored Textbook page of his website www. From the exercise files folder, open the Section2-Imperial. Set the Polar Tracking to 90, , , , as shown below: Notice that this file already has the four isolated footings and grids created. As a result, you will need to grip edit the height of the column after inserting.
Page 5 5. In this tutorial, you will insert a single column of that height. You now need to select the section type and section size from the next two flyouts. Close the dialog box. Before you start inserting the perimeter and filter beams, it is recommended to change the display type of the four columns. Select the four columns and then right-click in the blank area of the drawing window; the shortcut menu is displayed.
From the right pane, select Symbol; the four columns are displayed as system axes with the actual section displayed partially at the midpoint, as shown in the figure below: Page 7 The four beams to be inserted on the outside are AISC Page 8 You will now select the section type and size from the second and third flyouts. The model, after inserting the beams, is shown in the following figure: Page 9 Next, you will insert the filter beams. But first, you will isolate the peripheral beams you inserted in the previous steps.
With no tool active, select the four perimeter beams inserted in the above steps. Using the ViewCube, change the current view to the Top view. The model should appear similar to the one shown below: Page 10 Page 12 Notice that although you selected only one point labeled as 2, all the selected sections are still split along a plane at that point. Erase the beams such that the model appear similar to the one shown below: Select all the filter beams.
Page 13 Change all the beam types to AISC Change the view to Home view with parallel projection. The model should look similar to the one shown below: Select the four columns displayed as system lines and then right-click in the blank area of the graphics window. From the shortcut menu, select Advance Settings. Open the Section3-Imperial. Page 16 4. Page 17 Before you select the column, it is better to hide the Connection vault palette.
If you do not hide this palette, it will interfere with the joint dialog box. Page 18 Configure the settings, as shown below: Page 19 Configure the settings as shown below: Configure the settings as shown below: Page 20 Configure the settings as shown below: Page 21 The joint should look similar to the one below: Next, you will copy this joint at the base of the rest of the three columns. Page 22 Select one of the plates or bolts of the base plate joint you inserted in earlier steps; you are again prompted to select objects.
Select the remaining three columns and then press ENTER; the same joint is added to the remaining three columns as well. The model, after copying the joints, is shown in the following figure: Page 23 Page 24 Section 4: Inserting Stairs In this section, you will open the Section4-Imperial.
Open the Section4-Imperial. You will now insert stairs in this model using the start and the end points of the stair. The points to be used as the start and end are already created in this file for your reference. Navigate to the area shown in the following figure. Page 25 5. Select the point labeled as 1 in the figure above as the start point of the stair; you are prompted to select the second point of the stair.
Select the point labeled as 2 in the figure above as the end point of the stair; you are informed that the middle alignment is by default selected to align the stair. First of all, you will change the stringer and landing profiles. Configure the settings as shown in the figure below: Page 26 Configure the settings as shown in the figure below: Page 27 This ensures the bottom landings are not created. Next, you will change the step tread type. Configure the settings as shown in the figure below: Page 28 Next, you will change the dimensions of the end plate.
Configure the settings as shown in the figure below: Page 29 Next, you will modify the landing parameters. Configure the settings as shown in the figure below: Page 30 You will accept the default angle section size. Configure the settings as shown in the figure below: Next, you need to modify the parameters of the bottom landing and the first tread.
Navigate to the bottom of the stair. Page 31 Notice that the first tread is not the same as the remaining treads. Therefore, you need to modify this tread to match the remaining treads.
This completes the insertion of stairs. The model, after inserting the stairs, is shown in the following figure: Page 32 Section 5: Numbering Single Parts and Assemblies In this section, you will open the Section5-Imperial. Open the Section5-Imperial. This model has another stair, handrails and joints added. Configure the settings in the dialog box, as shown below: Page 33 4. Notice the part mark shown as internalXXX. This is because currently there are no drawings generated for these main parts.
Once the drawings are generated, you will run the numbering again for these main parts to get their numbers from the drawings. You will notice that the single parts also display internalXXXX as the numbers.
Once the single parts are numbered, 6. Save the file. So you need to change the Management Tools settings for this. Page 35 Next, you need to update defaults to reflect this change.
You will first generate the single part drawings of the selected beams. Page 37 9. Once the drawings are generated, zoom close to the bottom of one of the columns, refer to the figure below. Select the base plate of the base plate joint and then right-click to display the shortcut menu, as shown in the figure below.
Page 38 Page 40 Section 8: Running the Numbering Again Because you used the process of generating the single part and assembly numbers based on the drawings, you will now run the numbering again to update the single part and assembly numbers to update the numbers of the objects whose drawings are generated.
Scroll down in the window and notice that there are three main parts that show proper part marks, as shown below: 4.
Right-click on the base plate of one of the base plate joints and click Select Similar from the shortcut menu, as shown in the figure below; all the plate objects are selected. Page 42 5. Press the ESC key to make sure nothing is selected from the model. Page 44 Once the assembly list with exploded bolts is generated, it will be opened in a separate window. Using the Green list at the top of this window enclosed in the Red rectangle in the figure below , cycle through various pages of this report.
Page 45 9. Save the beam list.
Ben roethlisberger wikipedia