Be respectful, keep it civil and stay on topic. We delete comments that violate our policy , which we encourage you to read. Discussion threads can be closed at any time at our discretion. Post a comment. General Form Factor. Chipset Type.

Author:Vudogami Akik
Language:English (Spanish)
Published (Last):20 September 2017
PDF File Size:8.62 Mb
ePub File Size:17.93 Mb
Price:Free* [*Free Regsitration Required]

Quick Links. Download this manual. Table of Contents. KD7 Series. Amd athlon xp system board socket kw7 series 72 pages. Kv7 series amd athlon xp system board socket 72 pages. Page 2 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual.

No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. Page 3: Table Of Contents Page 4 Page Chapter 1. Otherwise, the functions may not work normally. Page Layout Diagram Kd7 Chapter 1 Page Chapter 2.

Hardware Setup Hardware Setup Chapter 2. Failing to do so may cause the motherboard components or add-on cards to malfunction or damaged. The CPU you bought should have a kit of heatsink and cooling fan along with.

Please refer to the figure shown here to install CPU and heatsink. Table Connectors, Headers and Switches Here we will show you all of the connectors, headers and switches, and how to connect them. Please read the entire section for necessary information before attempting to finish all the hardware installation inside the computer chassis.

Page 29 Hardware Setup 2. Page 30 Chapter 2 3. Short pin-2 and pin-3 only when you want to clear the CMOS memory. The default setting is pin-1 and pin-2 shorted for normal operation. Page 31 Hardware Setup 4. Page 32 Chapter 2 5. Page 33 Hardware Setup 6. This motherboard supports standard IR transfer rates. Page 34 Chapter 2 7.

Watch the power LED pin position and orientation. Page 36 9. Page 37 Hardware Setup The SM bus is a specific implementation of an I C bus. I C is a multi-master bus, which means that multiple chips can be connected to the same bus and each one can act as a master by initiating a data transfer.

Page 38 Chapter 2 KD7 Series Page 39 Hardware Setup Please refer to our Web site for more information on graphics cards. Page 40 Chapter 2 FDD1 Connector There are 34 wires and two connectors on each floppy cable providing two floppy disk drives connection.

Connect the single end at the longer length of ribbon cable to this FDD1, and the two connectors on the other end to the floppy disk drives. Page 41 Hardware Setup Each cable has pin conductor and three connectors, providing two hard drives connection with motherboard. Page 42 Chapter 2 If you want to connect two hard drives together through one IDE channel, you must configure the second drive to Slave mode after the first Master drive.

Page 43 Hardware Setup Page 44 Chapter 2 Page Chapter 3. This program will not be lost when you turn the computer off. This program is also referred to as the boot program. It is the only channel the hardware circuit has to communicate with the operating system. This option is for setup of future CPUs whose specifications are still unknown.

The specifications of all present CPUs are included in the default settings. Unless you are very familiar with all CPU parameters, it is very easy to make mistakes when you define the external clock and the multiplier factor by yourself.

However, if the new CPU is slower than the old one and is the same brand and type , we offer you two methods to successfully complete the CPU change operation. Method 1: Setup up the CPU for the lowest speed for its brand.

Figure Time hh:mm:ss : You can set the time in this item: hour hh , minute mm and second ss. Most current HDDs have already been subjected to low-level format at the factory, so you can probably skip this operation.

The minimum number you can enter is 0, the maximum number you can enter is Precomp: The minimum number you can enter is 0, the maximum number you can enter is Advanced BIOS Features Setup Screen Virus Warning: When this feature is enabled, if there is any attempt from a software or an application to access the boot sector or the partition table, the BIOS will warn you that a boot virus is attempting to access the hard disk.

Quick Power On Self Test: After the computer has been powered on, the BIOS of the motherboard will run a series of tests in order to check the system and its peripherals. Drive A can be set as drive B and drive B can be set as drive A.

Otherwise, set it to No. The default setting is No. They may need a longer amount of time to initialize and prepare for activation. The system may be unstable or unable to boot up if your DRAM module does not support the clock you set.

Page 56 Chapter 3 Precharge to Active Trp : Trip timing value Precharge time — time from precharge command to when back can be activated. You can key in the HEX number into this section. The minimum number is , and maximum number is 00FF. Page 58 Chapter 3 module, then clock buffer will feedback a signal to northbridge. The value you set will effect the delay time for DCLK output signal.

The default setting is Disabled. This implements a single delay when writing to the AGP Bus. When you set it to Enabled, two-wait states are used by the system, allowing for greater stability. If it is set to Disabled, data transmissions are not buffered and CPU must wait until the data transmission is complete and then start another transmission cycle. The default setting is Enabled. When set to [Enabled], two additional channels will be provided for adding high performance devices to system.

Power Management Setup Menu This menu allows you to set up the power management in order to reduce power consumption. The processor complex context is not maintained. Resume by Ring: Two options are available: Disabled or Enabled.

This option can solve the display inversion to black after you have used the MPEG card. PC Health Status You can set the warning temperature for your computer system, and you can check the fan speeds and power supply voltages of your computer system.

The features are useful for monitoring all the important parameters within your computer system. Load Fail-Safe Defaults Figure Set Password Figure Set Password Screen Shot Set Password: You can enter but do not have the right to change the options of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password.

Page Appendix A. The installation procedures and screen shots in this section are based on Windows XP operating system. Page 78 Appendix A 6. Choose [Yes, I want to restart my computer now. Page Appendix B. Install Audio Driver The installation procedures and screen shots in this section are based on Windows XP operating system.

For those of other OS, please follow its on-screen instruction. Page 80 Appendix B Note: To keep a normal operation of 5.

Page Appendix C. The following screen appears.

AC 120-94 PDF

ABIT KD7-G - motherboard - ATX - Socket A - KT400 Specs



Abit KD7-B User Manual



ABIT KD7 Manuals


Related Articles